A Garage Door’s spring is a mechanical component to the garage door, and because of the pressures placed upon it to both raise and lower the door, the springs will eventually go bad. The problem with garage door springs is that it’s not the easiest component to fix. As we’ve talked about here before, because of the pressures behind those springs, for the amateur, or even professional for that matter, those springs can represent serious bodily pain, loss of limb or maybe even life. It’s best to call a professional if you don’t have either the knowledge or practice replacing these springs.

When a spring does break, it could be at the worst possible time—when you are hoping to leave for work, school, etc. You will know a spring has broken when the garage door wont open or close—this could also be a sign of other problems such as a faulty garage door opener, etc., and the list of ways in which to troubleshoot a stuck garage door can be found in February’s blog post. If you’ve determined that the spring is at fault, call a professional technician at Bailey’s Garage Door. If you continue to try and engage the spring by continuing to try to open and close the garage door, it could do severe damage to the door.

So, how do you prevent this moment in time in which you’re stuck with a broken garage door, hoping that a Garage Door Technician is available soon! There may have been warning signs before the door became stuck, warning signs that you could have caught early, and avoided the stuck disaster. Unfortunately, however, garage door springs wont break in standard ways, but often it might provide clues as to its wear. Firstly, if your garage door is stopping as it’s opening or closing this could be a sign of a damaged spring. Check the springs when the door is fully closed, and look for any noticeable damage or wear to the spring. Another clue is how the door is situated in the opening. Is the door crooked? Does it seem to be off its track? These could be definite clues that point to a faulty spring. Also, there’s the standard practice of if it looks broke then fix it! If there’s noticeable wear, or if you’ve had a simple accident such as backing into the door, or clipping the door with your car as you passed underneath, this would be a definite time to have the springs checked, and, possibly, replaced. You don’t want to find yourself with your car stuck in or just outside the garage at a time of emergency.

For all of your garage doors needs, please contact Bailey Doors today!

The post Garage Door Springs Billings MT appeared first on Bailey Garage Doors.

A garage door should receive a tune-up at least once a year, and although that seems like a difficult task it becomes easier as long as you follow these simple steps.

Look for Problem Spots
The first step in your garage door tune-up is to look for any obvious problem spots in your garage door system. Rollers should be in working order, the seal around the door should be pliable and the door itself should not be dented or warped. Any parts that are overly worn or damaged should be replaced.

It is also important to disconnect the power to the garage door opener before looking over your garage door system. The last thing you want is to have your garage door to open while you’re working.

Lubricate the Roller
If you have metal rollers, they can be easily lubricated with WD-40. If you have vinyl or rubber rollers, you will have to use another lubricant since WD-40 can damage non-metal components.

Re-Align Locking Bars
Misaligned locking bars are common and can prevent the garage door from sliding into the slots on the door track and locking into place. If the locking bars are misaligned, loosen the screws on the guide brackets that hold the locking bars in place and tap them gently into place with a hammer until they are aligned with the slots. Tighten the screws when you’re finished.

Inspect and Clean Moving Parts
Your garage door has several moving parts, which is why it is subject to so much wear and tear. Loose bolts and screws will all need to be tightened, and any gummy parts will need to be removed and soaked in mineral spirits. To make sure all parts that are removed are put back in the right place, try to only remove one part at a time.

Lubricate Chains and Springs
The chains of a garage door system can be lubricated with white lithium grease, while the springs will require a silicone-based spray. The springs are under a lot of tension and can pose a safety hazard, so don’t be afraid to contact a professional to inspect or replace them safely.

For more information on garage door repairs or any of your garage door repairs, please follow us on Facebook or Twitter or feel free to contact us!

The post Garage Door Tune Up Billings MT appeared first on Bailey Garage Doors.